loader image
RENNtech Mercedes-AMG GT C Roadster in yellow, front three-quarter view on the road

One build AMG GT C Roadster · C190

SunbeamYellow

Sunbeam Yellow, carbon fiber everywhere, and nothing added to the engine

550 HPM178 4.0 liter V8 BiTurbo
3.6 SECZero to sixty, roof up or down
196 MPHFactory rated top speed
RENNtech build

Not every build
starts with a dyno.

The AMG GT C Roadster arrives with the hard part already solved. 550 horsepower, a transaxle layout, rear-axle steering and the wide rear body it borrows from the GT R.

What it does not arrive with is aerodynamics that match the chassis, brake hardware that survives a Florida summer, or a stance that does the shape justice. Those are the three things this car needed, and the three things RENNtech changed.

So there is no turbo kit on this one. No ECU file, no larger injectors, no chasing a number. Carbon fiber where it earns its place, brakes that take the heat, and a lowered stance. The engine was left exactly as Affalterbach built it.

Mercedes-AMG GT C Roadster, C190

Sunbeam Yellow over black

RENNtech carbon fiber hood, rear wing, front splitter and fender extractors

RENNtech two-piece brake rotors and lowering kit

Built at RENNtech, Stuart, Florida

Talk to us about a build

The hood

Carbon fiber,
where it counts.

The RENNtech carbon fiber hood does two jobs at once. It takes weight off the front axle, the one place on a front-engined GT where weight hurts most, and it opens vented paths for the heat a hot-vee V8 generates to leave the engine bay instead of sitting in it.

It is laid up in pre-preg carbon fiber and finished with a high-gloss UV protectant clear coat, so the weave stays black rather than fading to brown after two summers outdoors.

Aerodynamics

Three parts.
One airflow problem.

Aero works as a set or it does not work at all. Add downforce at one end of a car and you have simply moved the problem to the other end. These three were developed to balance each other.

01

Fender extractors

At speed, pressure builds up inside the front wheel housings and has nowhere to go. The extractors give it an exit through the side of the fender instead of under the car.

The result is more front-end downforce and less of the understeer the AMG GT can show on turn-in.

Shop fender extractors

02

Front splitter

A one-piece part molded from 100 percent pre-preg carbon fiber, finished with a high-gloss UV protectant clear coat.

It sharpens the leading edge of the car and sets up the airflow everything behind it depends on.

Shop the front splitter

03

Carbon fiber rear wing

Developed through 3D scanning, CAD surfacing, CFD analysis and 3D-printed prototypes before a single part was made.

Each element is produced in Germany from pre-preg carbon fiber and mounted on custom titanium hardware, to OEM-standard fitment.

Shop the rear wing

Close-up of the vent in the RENNtech carbon fiber hood for the Mercedes-AMG GTShop the hood
Carbon fiber hoodVented, pre-preg
RENNtech carbon fiber rear wing fitted to the yellow Mercedes-AMG GT C RoadsterShop the wing
Carbon fiber rear wingMade in Germany

Brakes and stance

Lighter discs.
Lower car.

The RENNtech two-piece rotors pair a high-carbon iron disc with an aerospace-grade aluminum hat. Lighter than the factory disc, slotted rather than drilled, with directional curved vanes that pump air through the rotor to keep heat soak away. When the iron ring eventually wears out, you replace the ring, not the assembly.

The RENNtech lowering kit works with the adaptive damping already on the car. It closes the arch gap and drops the center of gravity without costing you the ride quality that makes a roadster worth owning.

Specification

Every part
on this car.

Each RENNtech part below links straight to its page in our store.

Engine & performance

  • M178 4.0 liter V8 BiTurbo
  • Hot inside-vee turbocharger layout
  • 550 hp, factory rated
  • 502 lb-ft of torque
  • 0 to 60 mph in 3.6 seconds
  • 196 mph top speed
  • 7-speed AMG SPEEDSHIFT DCT

Chassis as delivered

  • Rear-wheel drive, transaxle layout
  • Active rear-axle steering
  • Electronic rear limited slip differential
  • AMG RIDE CONTROL adaptive damping
  • Wide rear body shared with the GT R
  • Three-layer fabric roof

Finish

  • Sunbeam Yellow
  • Black fabric roof
  • Gloss carbon fiber throughout
  • Black exterior trim
  • Quad exhaust outlets

Built at

  • RENNtech Inc.
  • Stuart, Florida
  • Designed, engineered and made in the USA
  • Parts available individually or as a package
  • Fitting in house or shipped worldwide

Factory figures are as rated by Mercedes-AMG for the GT C Roadster. The RENNtech parts on this build are aerodynamic and chassis components. The engine and its calibration were left standard. Want more power as well? The ECU+ upgrade for the GT C takes the M178 to 659 hp.

The car

Every angle.

Questions

What owners
ask us first.

Every element of the wing is produced in Germany from pre-preg carbon fiber, finished with a high-gloss UV protectant coating and mounted on custom titanium hardware. RENNtech developed it with 3D scanning, CAD surfacing, CFD analysis and 3D-printed prototypes before the first part was laid up, which is why it sits on the car with OEM-standard fitment rather than looking like an afterthought.

Yes. They are designed to optimize airflow and reduce the pressure that builds up inside the front wheel housings at speed. Letting that air escape sideways instead of fighting its way out under the car improves front-end downforce and helps counter the understeer the AMG GT can show on turn-in. They happen to look good as well, but that is the second reason they exist, not the first.

The C190 family shares a great deal, and most of the RENNtech aero for the AMG GT is offered across the GT, GT S, GT C and GT R in coupe and roadster form. The front splitter is sold in two versions, one for 2015 to 2017 cars and one for 2018 and later. Fitment varies by model year and by what the car already has fitted, so send us the VIN and we will confirm the exact part numbers before you order anything.

A RENNtech rotor is a two-piece design: a high-carbon iron disc on an aerospace-grade aluminum hat. It is lighter than the standard disc, it runs directional curved vanes that pump air through the rotor to fight heat soak, and when the iron ring is finally worn out you replace the ring rather than the whole assembly. Drilled factory discs tend to stress-crack around the holes and chew through pads unevenly. These are slotted instead, which clears pad debris and stops water sitting between pad and disc, and they take several sets of pads per rotor.

No. The RENNtech lowering kit is matched to the AMG adaptive damping already on the car, so it closes the wheel arch gap and drops the center of gravity without turning the GT C into something you do not want to drive to dinner. On a car that spends its life with the roof down in Florida, that matters.

That is exactly what we do. Every part on this GT C is a RENNtech product you can order individually or as a complete package, fitted at our workshop in Stuart, Florida, or shipped to you. Tell us which chassis you have and how you want the car to look and drive, and we will put the list together in the right order.

Build yours
the same way.

Every part on this GT C is a RENNtech product. Tell us what you drive and what you want from it, and we will put the list together in the order that makes sense.