ECU Upgrade
Our own calibration for the M178 4.0 liter V8 BiTurbo, developed in house on our dyno.
It keeps your original factory file, so the car can go back to stock through the OBD2 port whenever you want.


One build AMG GT C Roadster · C190
Solarbeam Yellow, carbon fiber everywhere, and a RENNtech® tuned V8
The AMG GT C Roadster arrives with the hard part already solved. 550 horsepower, a transaxle layout, rear-axle steering and the wide rear body it borrows from the GT R.
RENNtech took it further on every front. Under the hood, our ECU Upgrade with downpipes, a carbon fiber airbox, blow-off valve adapters and the Exhaust Valve Module. Outside, carbon fiber aerodynamics that match the chassis. Underneath, brakes that survive a Florida summer, a lower stance and RENNtech wheels.
And it is not finished. A RENNtech turbocharger upgrade is going on this car next, and the dyno sheet on this page will follow it.
Mercedes-AMG GT C Roadster, C190
Solarbeam Yellow over black
RENNtech ECU Upgrade, downpipes, carbon fiber airbox, BOV adapters and EVM
RENNtech carbon fiber hood, rear wing, front splitter and fender extractors
RENNtech two-piece brake rotors, lowering kit and wheels
RENNtech turbo upgrade: going on next
Built at RENNtech, Stuart, Florida
Talk to us about a buildPower
The parts that change how this car drives, all from RENNtech, all available for your GT.
Our own calibration for the M178 4.0 liter V8 BiTurbo, developed in house on our dyno.
It keeps your original factory file, so the car can go back to stock through the OBD2 port whenever you want.
High-flow downpipes that let the turbochargers breathe out as freely as they breathe in.
The calibration is written with them in mind, not added on top.
Pre-preg carbon fiber with flow-optimized turbo inlets, feeding the engine the air the calibration expects.
It looks the part when the hood is open, too.
They relocate the blow-off valves so the compressed air is released where it belongs.
Part of the reason the power holds pull after pull, not only on the first one.
Full control of the AMG sport exhaust valves on demand, whatever drive mode the car is in.
Loud when you want it, quiet when you leave at six in the morning.
A RENNtech turbocharger upgrade is going on this car next.
We will publish the new dyno sheet here when it is done.
Going on next
The hood
The RENNtech carbon fiber hood does two jobs at once. It takes weight off the front axle, the one place on a front-engined GT where weight hurts most, and it opens vented paths for the heat a hot-vee V8 generates to leave the engine bay instead of sitting in it.
It is laid up in pre-preg carbon fiber and finished with a high-gloss UV protectant clear coat, so the weave stays black rather than fading to brown after two summers outdoors.
Aerodynamics
Aero works as a set or it does not work at all. Add downforce at one end of a car and you have simply moved the problem to the other end. These three were developed to balance each other.
At speed, pressure builds up inside the front wheel housings and has nowhere to go. The extractors give it an exit through the side of the fender instead of under the car.
The result is more front-end downforce and less of the understeer the AMG GT can show on turn-in.
A one-piece part molded from 100 percent pre-preg carbon fiber, finished with a high-gloss UV protectant clear coat.
It sharpens the leading edge of the car and sets up the airflow everything behind it depends on.
Developed through 3D scanning, CAD surfacing, CFD analysis and 3D-printed prototypes before a single part was made.
Each element is produced in Germany from pre-preg carbon fiber and mounted on custom titanium hardware, to OEM-standard fitment.
Shop the hood
Shop the wing
Brakes and stance
The RENNtech two-piece rotors pair a high-carbon iron disc with an aerospace-grade aluminum hat. Lighter than the factory disc, slotted rather than drilled, with directional curved vanes that pump air through the rotor to keep heat soak away. When the iron ring eventually wears out, you replace the ring, not the assembly.
The RENNtech lowering kit works with the adaptive damping already on the car. It closes the arch gap and drops the center of gravity without costing you the ride quality that makes a roadster worth owning.
And it sits on RENNtech wheels, which finish the stance the lowering kit starts.
Specification
Each RENNtech part below links straight to its page in our store.
The 550 hp figure is the factory rating for the GT C Roadster as delivered. This car runs the RENNtech ECU Upgrade with downpipes, carbon fiber airbox, Blow-Off Valve Adapters and Exhaust Valve Module, and a RENNtech turbo upgrade is going on next. Measured figures go in the dyno sheet.
The car
Questions
Every element of the wing is produced in Germany from pre-preg carbon fiber, finished with a high-gloss UV protectant coating and mounted on custom titanium hardware. RENNtech developed it with 3D scanning, CAD surfacing, CFD analysis and 3D-printed prototypes before the first part was laid up, which is why it sits on the car with OEM-standard fitment rather than looking like an afterthought.
Yes. They are designed to optimize airflow and reduce the pressure that builds up inside the front wheel housings at speed. Letting that air escape sideways instead of fighting its way out under the car improves front-end downforce and helps counter the understeer the AMG GT can show on turn-in. They happen to look good as well, but that is the second reason they exist, not the first.
The C190 family shares a great deal, and most of the RENNtech aero for the AMG GT is offered across the GT, GT S, GT C and GT R in coupe and roadster form. The front splitter is sold in two versions, one for 2015 to 2017 cars and one for 2018 and later. Fitment varies by model year and by what the car already has fitted, so send us the VIN and we will confirm the exact part numbers before you order anything.
A RENNtech rotor is a two-piece design: a high-carbon iron disc on an aerospace-grade aluminum hat. It is lighter than the standard disc, it runs directional curved vanes that pump air through the rotor to fight heat soak, and when the iron ring is finally worn out you replace the ring rather than the whole assembly. Drilled factory discs tend to stress-crack around the holes and chew through pads unevenly. These are slotted instead, which clears pad debris and stops water sitting between pad and disc, and they take several sets of pads per rotor.
No. The RENNtech lowering kit is matched to the AMG adaptive damping already on the car, so it closes the wheel arch gap and drops the center of gravity without turning the GT C into something you do not want to drive to dinner. On a car that spends its life with the roof down in Florida, that matters.
That is exactly what we do. Every part on this GT C is a RENNtech product you can order individually or as a complete package, fitted at our workshop in Stuart, Florida, or shipped to you. Tell us which chassis you have and how you want the car to look and drive, and we will put the list together in the right order.
Every part on this GT C is a RENNtech product. Tell us what you drive and what you want from it, and we will put the list together in the order that makes sense.